IEC 60268 7 PDF

IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.

Author: Gardanris Kigagar
Country: Samoa
Language: English (Spanish)
Genre: Finance
Published (Last): 14 March 2012
Pages: 409
PDF File Size: 16.56 Mb
ePub File Size: 18.31 Mb
ISBN: 567-9-55436-361-8
Downloads: 78410
Price: Free* [*Free Regsitration Required]
Uploader: Moogusida

If the answer is No, the sequence jumps to post-processing steps which calculate passive attenuation and the final display step. A statistics step calculates the mean of the 3 unoccluded measurements.

Noise speakers are set up adjacent to the HATS left and right ears. Calibrate the microphones per the instructions in the SoundCheck manual. Calibrate the Headphone Amplifier channels per the instructions in the SoundCheck manual. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Hardware Requirements In order to run the sequences, the following hardware is required: A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display.

We use cookies to make our website easier to use and to better understand your needs. Setup System, Hardware and Calibration Before attempting to run any of the sequences, read the following setup instructions. Click to learn more.

IEC Headphone Test Sequences – Listen, Inc.

If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. Find Similar Items This product falls into the following categories.

  LENNEBERG 1967 BIOLOGICAL FOUNDATIONS OF LANGUAGE PDF

The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed uec derive their SPL values. Sound System Equipment — Part 7: The data from each loop iteration is displayed as it is acquired.

IEC-60268-7 Headphone Test Sequences

You may experience issues viewing this site in Internet Explorer 9, 10 or A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. Headphone Voltage Sensitivity Final Display. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of ice If the answer is Yes, the user is prompted to turn the ANC on and the sequence repeats the passive measurements.

The folder contains dependent files required to run the sequences.

The Hz recorded time waveforms are processed using heterodyne analysis to derive their fundamental values. Search all products by. Registration required The content you have requested is available only to registered visitors. The sequence then goes through a series of acquisition steps to generate four fundamental curves which 77 then post-processed to calculate crosstalk.

Headphones and earphones Status: You may find similar items within these categories by selecting from the choices below:.

Take the smart route to manage medical device compliance. Crosstalk and radiation curves are then ied on the final display. Test Setup for measuring headphone voltage sensitivity. Relink dialog Here is a list of sequences and their default signal isc unique paths are in bold: A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.

  CAV 71B PDF

BS EN 60268-7:2011

Matthew Miller November 15, – 6: It then calculates the voltage required to produce 1 mW into the rated impedance. If more than 4 input channels are available, all input signal paths may be assigned to separate hardware channels. Once calibrated, position the microphones 0. You are ready to start the sequence. This sequence uses a pink noise stimulus to iwc the passive, active and total attenuation of noise cancelling headphones. Connect the impedance boxes between the headphone amp out and headphone input.

This sequence satisfies the requirements of Section iwc. Your basket is empty.

BS EN – Sound system equipment. Headphones and earphones

Five separate sequences are provided, each designed to measure specific characteristics. The sequence first plays a stepped sine through both channels of the DUT and captures the sound radiation from the DUT using 2 reference mics. The standard itself is a lengthy document, 9 Sections and 3 Annexes covering 46 printed pages.

No – I don’t want to receive the latest audio test information by email. Software Requirements SoundCheck