FUTABA 3PK MANUAL PDF

Channel radio control system instruction manual • Read online or download PDF • Futaba 3PK User Manual. View and Download FUTABA 3PK instruction manual online. 3-CHANNEL RADIO CONTROL SYSTEM. 3PK Remote Control pdf manual download. View and Download FUTABA 3PKS instruction manual online. download. Also for: Magnum 3pk super. Remote Control FUTABA 3PK Instruction Manual.

Author: Kazshura Kagaran
Country: Russian Federation
Language: English (Spanish)
Genre: Finance
Published (Last): 13 February 2015
Pages: 306
PDF File Size: 17.73 Mb
ePub File Size: 13.88 Mb
ISBN: 235-9-52623-162-8
Downloads: 35310
Price: Free* [*Free Regsitration Required]
Uploader: Nasar

Push the lever to the left or right up or down Operating by push button switch: Always try to setup your ESC normally first. To select janual type, use the Menu type select function See page Total timer The total timer shows the accumulated time from last reset. Page 66 – ABP: Used when the mechanical setup in the vehicle does not provide the exact desired amount of steering, or the throttle servo is trying to open the carburetor past wide open, or does not open it far enough The current position is displayed on the LCD screen in the bottom three rows of the list.

Due to the shape of some nitro engine linkages, throttle servo movement near neutral results in very little movement of the pushrod. Variable Trace Rate is a type of throttle exponential, which is basically a 3-point manua, where one point may be raised or lowered, forming two straight lines, and where 3pl user can select the point futwba the line breaks into two.

We immediately began to evaluate the backlog of Futaba parts and service requests, completing what could be done with available parts.

  CONVERTIDOR BESSEMER PDF

When ending setting, return to the initial screen by pressing the END button twice for direct selection, press the END button once.

The wheel angle futaa also left-handed operation. Other Precautions Always use only genuine Futaba transmitters, receivers, servos, FET amps electronic speed controls ,Nicad batteries and other optional accessories. However, failures can still occur which cause loss of this memory.

S Sets the rate at which the ser- DTY duty: Mechanical Atl Adjustment Mechanical ATL adjustment Make this adjustment when you want to decrease the stroke of the brake back side of the throttle trigger for operation feel.

Moves throttle servo to a preset position which closes the carburetor and shuts off the engine. Using the model selection function Model No. Counts negatively once desired time is passed below 0.

For digital ATL, see p. Cycle duty ratio, sets the proportion of brakes applied full vs. Use engine cut part of auto-start to shut engine off at end of run. Don’t have an account? If the trans- Cover mitter has not been used for some time, cycle the battery by charging and discharging it two or three times.

NEVER attempt to operate more than one model on the same frequency at the same time. 33pk DL2 is assigned another function, this function can be set with this screen. Operating by the lever: Used when model has separate front and rear brakes, and they must be adjusted separately.

This mixing uses the 2nd channel to control the rear brakes and the 3rd channel to control the front brakes. Table of Contents Add to my manuals Add. Prealarm can also be set. If the battery is charged fitaba a quick charger for other than digital RC systems, it may not be fully charged.

  CALCULO DIFERENCIAL E INTEGRAL GRANVILLE RESUELTO PDF

Part name NT8FB 9. Defaults to being adjustable with dial 3. Also called switch, or SW. When Requesting Repair for U.

Futaba 3PK GHz User Manual | 2 pages

If signals are output normally, RF output monitor “RF” will be displayed on the screen. Connect the wheel unit wiring harness 2.

Steering servo CH1 2: After you followed the suggestions listed and the problem is not corrected return the system to our service department for inspection and repair. Use this function when a mechanical off- set has occurred for some reason.

Amount of brake return, how far the braking response is decreased during the pulses. Operation – When braking, mixing mnual applied to 2nd channel 3rd channel. Ni-cad Battery Replacement The Ni-cad battery is connected by a connector so that it can be removed when you will not be using the transmitter for a long time, or when replacing a dead battery with a spare battery.

Level lv3 only servo view servo – Futaba 3PK User Manual

If “RF” is not displayed, check if the transmitter crystal and RF module are installed. The programmable mixing 1 and pro- grammable mixing 2 set-up screens are independent. If it does not, the system is ready for use.