For coated-steel sheet products, the standards are written by ASTM Committee A05, a body obtain a copy of the appropriate ASTM Standard. A /A M. ASTM AAM 薄镀层电解镀锌薄钢板 – Designation: A /A M – 98 AMERICAN SOCIETY FOR TESTING AND M. Find the most up-to-date version of ASTM A at Engineering

Author: Zur Tujind
Country: Eritrea
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 19 June 2010
Pages: 295
PDF File Size: 16.93 Mb
ePub File Size: 7.21 Mb
ISBN: 758-1-99736-176-2
Downloads: 93341
Price: Free* [*Free Regsitration Required]
Uploader: Vull

The thickness is the total of the ast, metal and the coating. These devices are ast for use as a basis for determining suitability for shipment provided that they have been calibrated properly. We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. For each finish product specified, two samples, minimum size 6 inches mm square, representing actual product, color, and finishes.


Current PDF there are thousands of pdf files on the internet. These grades have varying ability to be formed. This is done regularly for various types of doors and small buildings. Property Data This page displays only the text of a material data sheet. Doors shall be installed and fastened to maintain alignment with frames to achieve ast, operational effectiveness and appearance.

Coordinate with door opening construction and door frame and door hardware installation. Please a91 us at x591 matweb. For electrolytic zinc-coated steel sheet with coating masses heavier than described in this speci?

Minimum thickness as follows:. Users requiring more precise data for scientific or engineering calculations can click on the property value ast see the original value as well as raw conversions to equivalent units. Current edition approved May 10, Click here to view all the property values for this datasheet as they were originally entered into MatWeb. Please read our License Agreement regarding materials data and our Privacy Policy. Clean and restore soiled surfaces.


Packaging and Package Marking 9. Thus modern electroplating facilities are frequently equipped asstm X-ray?

The specimen shall be cut not less than 2 in. This specification is based on steel doors and steel frames that are manufactured without deviation from SDI standards. Originally published as A — Prepare all frames for all mortise template hardware and reinforced only for surface mounted atm.

Non-standard units can result astm a added cost and lead time. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Delete entirely if factory finish is not required. Provide details of door design, door construction details astm a methods of assembling sections, hardware locations, anchorage and fastening methods, door frame types and details, anchor types and spacing, and finish requirements.

Cold reduced sheet steel material in coil form hot rolled pickled is sometime used is uncoiled and passed continuously through the astm a line equipment.

ASTM A591 DS galvanized steel coils & sheets

This product is available in four zinc-coating designations which are listed in Table 1. If one surface is protected suitably during the initial stripping, coating mass can be determined for each surface independently. Data sheets for overmetals, plastics, ceramics, and composites. Face steel sheet shall astm ast at least one or more of the following requirements:.

ASTM A591 EDDS galvanized steel coils & sheets

Subscribe to Premium Services Searches: Provide hollow metal doors and frames from SDI Certified manufacturer. Delete the paragraph not required. We appreciate your input. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.


ASTM A DS galvanized steel coils & sheets

We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. Click here to view all astm a property values for this datasheet as they were originally entered into MatWeb.

NOTE 1—A typical ordering description in inch-pound units is as follows: Do not begin astm a until conditions have been properly prepared. Login to see your most recently viewed materials here. CNC Gantry type machining center Max process size: Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Or if you don’t have an account with us yet, then click here to register.

This section is based on the products of the Association, which is located at:. Within the text, the SI units are shown in brackets. Members of the Steel Door Institute manufacture standard steel doors and q in accordance with these standards. To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below.