L. S. L. Elements. (C) Carbon, max. (Mn) Manganese, max. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality ASTM A Stainless Steel Rectangular Tube, ASTM A Global Steel is one of the leading manufacturers, Supplier and exporters of High Quality ASTM A Steel Pipes, ASTM A Polished Stainless Steel Pipes.
|Published (Last):||13 March 2013|
|PDF File Size:||12.99 Mb|
|ePub File Size:||18.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Historical Version s – view previous versions of standard. Elongation in 2 in. Ratio of Wall Thickness to Outside Diameter.
The grades covered are listed in Table 1. Bright Annealed, Polished Trade Name: Twist Asrm 3 ft. Small outside diameter tubes are defined as those less than aatm. A welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed in a number of standard sizes and grades. We can offer polished stainless steel pipes in NO. A Grade L Tube.
Ovality is astn difference between maximum and minimum outside diameters measured at any one cross section. This guide covers standard specification for welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed. Permissible Variations in Cut Length in. Tolerances — Diameter, Wall— Round Tubing. Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A polished stainless steel ornamental tubes are widely used for building constructions and architectural applications.
Specified Size, Outside Diameter, In. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Also see Footnote B. Tolerances Hot Finished Round Table. The aztm of maximum and minimum outside diameter readings should fall within the outside diameter tolerances as shown in this table. For square or rectangular structural tubing with heavier walls, the radius of any outside corner of the section shall not exceed three times the specified wall thickness.
Heat analysis shall be performed wherein several grades of steel shall conform to the q554 chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, titanium, columbium, and tantalum. E These tolerances apply to cut lengths up to and including 24 feet. Yield Strength min, ksi MPa. Tubes shall be furnished in one of the following shapes – round, square, rectangular, or special. For sized over 5-in.
Nominal Pipe Size Inches. This abstract is a brief summary of the referenced standard. A Grade Tube.
ASTM A554 304/304L/304H Stainless Steel EFW Tubes
Largest Specified Outside Dimension, Inches. Click here For more ss material price list. B For ovality values, the tolerance for average outside diameter at any one cross section does not exceed the outside diameter tolerance value for the applicable outside diameter. The tubes shall be made from flat-rolled steel by an automatic welding process without the addition of filler metal.
Where ellipses … appear in this table, there is no minimum and analysis for the element need not be determined or reported. For sizes up to and including 5-in. Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.
Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Small outside diameter tubes are defined as those less than 0. The straightness tolerance is 0.
ASTM A, ASTM A, ASTM A – Chicago Tube & Iron
A These tolerances apply to cut lengths up to and including 24 feet. Tensile Strength, min ksi MPa. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Link to Active This link will always wstm to the current Active version of the standard. Up to 6 meters, custom cut lengths Thickness: Radii of Corners, max. Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified a55 S