1766 UM001 EN P PDF

Publication UMA-EN-P – November Table of Contents . User Manual UM to assign an IP address to the MicroLogix. controller. Publication INC-EN-P – October Important . Manual UM .. publication UM, for more information on surge suppression. rm_-en-p – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Document Number IN UM

Author: Gronos Mikree
Country: Paraguay
Language: English (Spanish)
Genre: Automotive
Published (Last): 27 July 2007
Pages: 337
PDF File Size: 6.34 Mb
ePub File Size: 19.44 Mb
ISBN: 324-9-60010-724-2
Downloads: 75586
Price: Free* [*Free Regsitration Required]
Uploader: Shasar

Ensure that the battery wire connector is inserted into the connector port if your application uj001 battery power. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts.

Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings that are required rn comply with certain product safety certifications.

Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. In no event will Rockwell Automation, Inc. Remove the mounting fn. Soal meeting 9th Part of speech: See UL File E Trademarks not belonging to Rockwell Automation are property of their respective companies.

Place a flat-blade screwdriver in the DIN rail latch at the bottom mu001 the controller. When you connect or disconnect the battery an electrical arc o occur. Follow these steps to install your controller on the DIN rail. For more information, contact your local distributor or Rockwell Automation representative, or visit http: The Belden cable has two signal wires black and clearone drain wire, and a foil shield.

  ATHA PUKU PDF

Throughout this manual, when necessary, we use notes to make you aware of safety considerations. Repeat steps 1 and 2 for the second DIN rail latch.

Holding the controller, pry downward on the latch until the latch locks in the open position. When using spade lugs, use a small, flat-blade km001 to pry the finger-safe cover from the terminal blocks, then loosen the terminal screw.

1766-IN001 – Rockwell Automation

Store the equipment in appropriate static-safe packaging when not in use. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc. Remove the mounting template from inside the back cover of this document. Umm001 the top of the DIN rail slot from the rail. WARNING Identifies information about practices 1676 circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.

This equipment is supplied as open-type equipment. The interior of the enclosure must be accessible only by the use of a tool.

Scripting must be enabled to use this site.

The drain wire and foil shield must be grounded at one end of the cable. Use a static-safe workstation, if available. Wiring Your Analog Channels Analog input circuits can monitor voltage signals and convert them to serial digital data as shown in the following illustration. Once wiring dn complete, be sure the controller is free of all metal fragments before removing the protective debris strip.

  EL HOMBRE SPIRITUAL WATCHMAN NEE PDF

Locate your controller as far as possible from power lines, load lines, and other sources of electrical noise such as hard-contact switches, relays, and ac motor drives. Power supply inrush current V AC: Power Loss in Transmission Lines. The input and output terminals of the MicroLogix controller are designed for the u001 spade lugs. Use AWG 14 wire.

IN – Rockwell Automation

Several specific steps can be em to help reduce the effects of environmental noise on analog signals: Debris strip ATTENTION Do not remove the protective debris strip until after the controller and all other equipment in the panel near the controller are mounted and wiring is complete. Prolonged exposure to direct sunlight could degrade the LCD display. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance.

By using suppression, you also reduce the effects of voltage transients caused by interrupting the current to that inductive device, and prevent electrical noise from radiating into system wiring. Specifically, this equipment is intended for use in clean, dry environments Pollution degree 2 1 and with circuits not exceeding Over Voltage Category II 2 IEC 3.

You must also provide an acceptable grounding path for each device in your application.