Honda outboard service/repair manual – Seloc | 4-stroke | 4 stroke | Table of Contents PDF file | 2 hp – hp – 4 hp – 8 hp – 40 hp – 50 hp – 75 . Clymer Honda Outboard Marine service and repair manuals are written with model specific coverage for your Honda Outboard Marine. From basic service and. View and Download Honda Outboard Motor BFA owner’s manual online. Honda Power Equipment Outboard Motor Owner’s Manual. Outboard Motor.
|Published (Last):||27 April 2004|
|PDF File Size:||3.77 Mb|
|ePub File Size:||1.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Use starting procedure p. The ignition switch can be used to start the mqnual only when the control lever p.
If a label comes off or becomes hard to read, contact an authorized Honda Marine servicing dealer for a replacement. Remove the two mud guard clips from the upper part of the under cover grommet.
The tachometer shows engine speed in revolutions per minute. Take outboard motor to an authorized Honda marine dealer, or hinda to the shop manual.
Honda Outboard Motor BF135A Owner’s Manual
Enter text from picture: Refueling Insert the mud guard clips with the inner part raised off, then push in the inner part securely until they click. Never smoke near gasoline, and keep hondaa flames and sparks away. Remove the old fuse by removing two 5 mm screws. Engine Oil Unhook the drain hose from the front bracket clamp.
Fuel hose not primed. Press the UP or DN down side of the switch to adjust the angle of the outboard motor. Use only a genuine Honda oil f ilter or a f ilter of equivalent quality specif ied f or your model.
It is necessary for the ignition switch to be in the ON position for the trim meter to indicate the motor angle.
If the engine fails to start within 5 hondda, release the key and wait at least 10 seconds before operating the starter again. You may purchase them from your Honda marine dealer. Disconnect the outboard motor from the boat, hoist the outboard motor, and move it to the storage area.
Reassemble the water separator body and the cup. This shows that water is circulating through the cooling system. Starting The Engine The emergency stop switch clip and lanyard system is a safety device that will stop the engine if you fall away from the controls while operating the boat.
The switch clip must be inserted in the emergency stop switch in order for the engine to start and run. We are certain you will be pleased with your purchase of one of the finest outboard motors on the market. Do not try to remove the mud guard clip with f orce without raising the inner part of the mud guard clip.
Check to be sure there are no fuel leaks before starting the engine.
Use the minimum throttle opening necessary to operate the boat at a safe trolling speed. Refer to the maintenance schedule page Apply anticorrosion oil to pivot surf aces where grease cannot hinda. Stop the engine and keep heat, sparks, and flame away. Shop Manual This manual covers complete maintenance and overhaul procedures.
To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.
Wipe up any spills before starting the engine. Please read maual carefully. Then move the tilt If oil pressure becomes low, the indicator will go off, and the engine protection system will limit engine speed.
The control lever cannot be moved from the N neutral position unless the neutral release lever is squeezed Honda power equipment outboard motor owner’s manual 49 pages.
HONDA OUTBOARD MOTOR BFA OWNER’S MANUAL Pdf Download.
It will also help reduce air pollution. The control lever cannot be moved away from the N neutral position unless the fast idle lever is lowered. Unlock and remove the engine cover p. Possible Cause Out of fuel. Propeller Replacement Before replacing the propeller, remove the clip from the engine stop switch to prevent any possibility of the engine being started while you are working with the propeller.
Never refill the fuel tank inside a building where gasoline fumes may reach flames or sparks. If water is accumulated, stop outblard engine, and clean the water separator following the instructions on pageor consult with an authorized Honda marine dealer.
Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system. Remove and inspect spark plugs. Check homda stern bracket to be sure the outboard motor is securely installed. And using this outboard motor safely is an important responsibility.