Dome Camera Installation Manual Weatherproof and Indoor versions www. Contents Introduction. Menu System Manual. Page 4 of 1. THE DENNARD TYPE DOME CAMERA. The Dennard Dome Camera is a precision unit, offering a wide. The Dedicated Micros Camera has a number of features which can be selected by the System. Supervisor when the dome is installed. Any of these can be.
|Published (Last):||15 May 2017|
|PDF File Size:||19.82 Mb|
|ePub File Size:||2.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Offer the bracket base casting into position and fasten to the wall using appropriate fixings. Vandal resistant Dennagd info Advanced privacy patches, preset positions and tour facilities. Arecont Vision Contera indoor dome series.
Control Switches – Indoor Dome Remove and retain the four screws securing the shield to the head and lift off the shield. In a domestic environment this product may cause radio frequency interference, in which case the dfnnard may be required to take adequate measures.
Dennard Dedicated Micros 2060 D PTZ Dome Camera CCTV
The external camera is weatherproof IP rated. Control Switches – Indoor Dome Use a spirit bubble level against one of the flats to align accurately.
Twist once located to secure, then tighten screw heads C to secure the dome enclosure to the mounting disk. Locate SW3 on the main PCB adjacent to the mounted connector attaching the daughter board housing the yellow and blue address switches.
Snap fit the tile mount bezel E. Dedicated Micros is pleased to announce that the Dennard Precision Dome is being upgraded with new features including:. Picture with intermittent control Cause 1. I have downloaded manuals and am getting confused. The configuration drawings show the three connection arrangements.
Attach the mounting disc A to the dome in the chosen position and use 3 of the existing M4 dome hd screws to attach the hemisphere to the dome. Dome Mounting – Weatherproof Dome Lift the dome to the bracket flange ensuring head of screws pass through the keyhole slots.
Camera Version To verify the version of camera supported by the dome software; 1. Cut or drill a hole in 200 ceiling in the sennard position using the pattern shown below. Locating the dome on the corner of a building will give an increased area of surveillance. I have fitted a BNC connector to the pigtail from the camera for UTC controlattached to the dennadd and patched to the monitor but I get no picture and cannot see any activity from the dome when I select the camera and move the joystick.
Attach safety bond to a suitable secure position in the ceiling void.
Dennard 2060 PTZ Speed Dome Camera 36 x Optical Zoom with Swan Neck (Fully re-furbished)
Attach safety bond to a suitable secure position in the ceiling void. These are accessed by removing the outer hemisphere and inner shroud, refer to Switch Configuration for more information.
Weight of dome should be supported by bond ensuring no stress is placed on centre connector B at any time. Always support dome with denard prior to mating connector B.
Dedicated Mircros Dennard Installation manual |
This product is marked dwnnard the CE symbol and indicates compliance with all applicable directives. When reassembling the dome, check the hemisphere sealing gasket is in place and that the hemisphere retaining screws are retightened to avoid water ingress.
When reassembling the dome, check the hemisphere sealing gasket is in place and that the hemisphere retaining screws are retightened to avoid water ingress. By ramformerApril 3, in General Digital Discussion.
Dennard Dedicated Micros D PTZ Dome Camera CCTV | eBay
Fit the cavity plugs A to the holes. Any pointers here would be great. This replaces the standard bezel F provided with the camera.
To Frame the image from a Fixed attitude camera; 1. The bracket casting can be oriented to position the cable entry hole below, on either side of at the top.
This operation cennard be carried out in an office type environment to avoid ingress of moist air. Attach bond to a suitable secure position in the ceiling void. From above, clamp to the tile via 2 x off split clamp rings C.
The mechanism needs to be removed from the dome to enable this.
Got it, continue to print. Adjust lift and gain settings.